![]() What can be the problem? Shall I use a smaller object size in the filter parameters again? Shall I scan the whole picture and not only a subarea (the door)? Now in commercial version no motion - or only the first motion after reconfiguring the detection filter - is detected in the archive stream! ![]() While using the free version this works perfect, every detected motion was marked in the timeline by a green area. My problem is: I go to the archive of the recorded stream and choose "search detected motion", after that I'm asked to mark an area where to search on the video screen. I want to mark every detected motion in the stream 1 second before and 10 seconds after detection and pushed the corresponding sliders to that positions. I defined a motion detection for the camera: marked a part of the picture (a door) with the brush in red and choose an object size a little bit bigger than the default size (because the default seems to be only a few pixels). I've installed the Xeoma server on a Centos-6-system and record permanently (by using the marker in the motion detection filter) the H264 stream from one IP camera. Please note, the speaker icon and microphone icon cannot be enabled at the same time.I'm a new customer. To record audio directly from the device, click on the microphone icon. Step 6: To hear audio from the camera's built-in microphone only, click on the speaker icon in the features pane. Step 5: Hover the mouse over the live feed to display the additional features pane located in the upper right-hand corner of the interface. Double click to load the feed into the interface. Step 4: In the Default Group, select your NVR and choose which device to access from the dropdown list. Step 3: Access the Main Menu and click on Live View. Step 2: Add the device into the software and ensure it is registered as "Online".įor more information on how to add a device into Amcrest Surveillance Pro, click here. Step 1: Launch Amcrest Surveillance Pro and log in. To download the Amcrest Surveillance Pro click here. Please note, the feature in this software can only listen and record audio from the device and does not support two-way audio. Mac users who do not have access to a web browser that supports Amcrest plugins can use our free Amcrest Surveillance Pro software to utilize the audio features of the NVR. Note: If you are using an external microphone, click on the Start Talk option available in the live view interface to hear the audio. If the camera supports two-way audio (built-in microphone and speaker) click on the microphone icon to activate the mic and speaker option on the camera. Step 6: To hear audio from the camera's built-in microphone only, click the speaker icon in the features pane. Step 5: Access the camera from the camera list and locate the additional features pane in the upper right corner of the screen. Step 4: Navigate to the Main Menu and click Live. Step 3: In the Encode menu, click on More Setting and verify audio is enabled and configured with the proper audio format (most Amcrest devices support AAC with 16K sampling) click Save. Step 2: In the Management menu, click on Camera>Encode and select the channel you wish to configure. For more information on how to access your device using IE mode, click here. Step 1: Access the device IE mode (or Internet Explorer) and log in. Note: If an external microphone is being used, ensure the microphone is active and plugged into the Audio In port on the back of the NVR using a mono RCA cable. For more information on how to utilize audio on your Amcrest NVR please refer to the information provided below. ![]() This can be achieved using IE Mode in Microsoft Edge or using the Amcrest Surveillance Pro software. If you are accessing the NVR through a web UI, audio capabilities will require the use of a plugin. The audio stream should be enabled by default if the camera supports audio however it is highly recommended to verify that audio is enabled on the camera if it is supported. ![]() If you are using a camera with built-in audio the NVR will automatically detect the presence of an audio stream. Audio recording and streaming capabilities are a standard part of almost all of the NVRs that we sell.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |